UG 工程图常用设置
句 柄 参 数 说 明 文字的显示
Drafting_dimTextCharSize: 0.1 ! Inches 字体大小 Drafting_dimTextAspectRatio: 0.7 宽高比 Drafting_dimTextSpaceFactor: 0.5 间隙因子 Drafting_dimTextLineFactor: 1 行间距因子 Drafting_dimTextColor: 6 颜色 Drafting_dimTextFont: kanji 字型
Drafting_dimTextWidth: normal (thick thin) Drafting_dimAppTextSpaceFactor: 0.500 Drafting_dimTolTextSpaceFactor: 0.500 Drafting_dimDimLineSpaceFactor: 0.500
剖面线
Drafting_crosshatchSpacing_MU: 2.0
ID 装配顺序号
Drafting_idSymbolSize: 0.27! Inches ID
截面线显示
Axs_sxlWidth: normal Axs_distPastPart_MU: 5.000 ! mm D
Axs_arrowSize_MU: 5.000 ! mm A Axs_stubbLength_MU: 3.0 ! mm E Axs_sectionLabelDist_MU: 5.000 ! mm
Axs_arrowLength_MU: 10.000 ! mm B
视图显示
UG_objectWidth: normal
半径符号R和直接符号 与尺寸间空格数
Drafting_diaRadSymAndDimTextDistance: 0.0
装配相关设置
Axs_assemblyXhatching: off UG_viewSectioningSlice: off
UG_macroRecordAllTransforms: on
Drafting_textArrowPlacement: arrowIn > arrowAUto Drafting_dimensionDecimalPlaces: 1>3
Drafting_sectionVwLabelViewScalePosition: above>below
Drafting_detailVwLabelScaleValueFormat: ratio>common Drafting_sectionVwLabelScaleValueFormat: ratio>sigle Drafting_otherVwLabelScaleValueFormat: ratio>ratio
字体(正常、粗、细) 尺寸/尺寸行间距因子尺寸/尺寸行间距因子尺寸/尺寸行间距因子剖面线间距 圆直径 线宽 箭头大小可见线线宽 1
剖面图 图标显示
Drafting_detailVwLabelViewLabelPrefix: \" \" —Drafting_detailVwLabelViewLabelPrefix: \"DETAIL\" Drafting_sectionVwLabelViewLabelPrefix: \" \"Drafting_sectionVwLabelViewLabelPrefix: \"SECTION\" Drafting_otherVwLabelViewLabelPrefix: \" \" —Drafting_otherVwLabelViewLabelPrefix: \"VIEW\"
Drafting_detailVwLabelParentType: note>embedded
Drafting_toleranceDecimalPlaces_Degrees: 1>3
Drafting_appendedTextSite: before>beforeAndAfter
Drafting_narrowDimensionDisplayType: textAboveStub>none
Drafting_diaRadSymAndDimTextDistance: 0.0>0.01
Drafting_angularUnits: degreesMinutes> fractionalDegrees
Drafting_angularToleranceUnits fractionalDegrees
直线/箭头
rafting_arrowSize: 0.1 ! Inches A Drafting_textLine: 0.04 ! Inches B Drafting_pointLine1: 0.04 ! Inches C Drafting_pointLine2: 0.0 ! Inches D Drafting_lineArrow: 0.03 ! Inches E Drafting_stubbSize: 0.0 ! Inches F
中心线显示
Drafting_centerlineExtension: 0.10 ! Inches Drafting_centerlineGap: 0.0625 ! Inches Drafting_centerlineXsize: 0.10 ! Inches
Drafting_centerlineAngle: 0.000 ! Valid Range is [0.0 to 360.0] Drafting_intersectExtension: 0.10 ! Inches Drafting_targetPointSize: 0.10 ! Inches Drafting_targetPointAngle: 0.000 ! Valid
视图视角
Drafting_projectionAngle: third ——first
缺省的环境变量指向ug_metric.def
UGII_DEFAULTS_FILE=${UGII_BASE_DIR}\\ug_metric.def
2
缺省绘图仪
UG_defaultPlotServerName: print 缺省队列名
UG_defaultPlotQueueName: HP
3
因篇幅问题不能全部显示，请点此查看更多更全内容